|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
DG9424/9425/9426 Vishay Siliconix Low-Voltage, Dual Supply, Low rON, Quad SPST Analog Switches FEATURES D 2.7- thru 12-V Single Supply or 3- thru 6-Dual Supply D On-Resistance--rDS(on): 1.7 D Fast Switching --tON: 42 ns --tOFF: 28 ns D TTL, CMOS Compatible D Low Leakage: 0.2 nA D 2000-V ESD Protection BENEFITS D D D D Widest Dynamic Range Low Signal Errors and Distortion Break-Before-Make Switching Action Simple Interfacing APPLICATIONS D D D D D D Automatic Test Equipment Data Acquisition Systems Communication Systems ADC Systems xDSL and PBX/PABX Audio Signal Routing DESCRIPTION The DG9424/9425/9426 are low voltage precision monolithic quad single-pole-single-throw analog switches. Combining high speed (tON: 42 ns), flat rDS(on) over the analog signal range ( ), minimal insertion lose (--3 dB at 190 MHz), and excellent crosstalk and off-isolation performance, the DG9424/9425/9426 are ideally suited for audio and video signal switching. The DG9424 and DG9425 respond to opposite control logic as shown in the Truth Table. The DG9426 has two normally open and two normally closed switches. Using BiCMOS wafer fabrication technology allows the DG9424/9425/9426 to operate on single and dual supplies. Single supply voltage ranges from 3 to 12 V while dual supply operation is recommended with 3 to 6 V. FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION DG9424/DG9425 TSSOP IN1 COM1 NC1/NO1 V-GND NC4/NO4 COM4 IN4 1 2 3 4 5 6 7 8 Top View 16 15 14 13 12 11 10 9 IN2 COM2 NC2/NO2 V+ VL NC3/NO3 COM3 IN3 TRUTH TABLE Logic 0 1 DG9424 OFF ON DG9425 ON OFF Document Number: 71807 S-31818--Rev. D, 01-Sep-03 www.vishay.com 1 DG9424/9425/9426 Vishay Siliconix FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION DG9426 TSSOP IN1 COM1 NC1 V-GND NC4 COM4 IN4 1 2 3 4 5 6 7 8 Top View 16 15 14 13 12 11 10 9 IN2 COM2 NO2 V+ VL NO3 COM3 IN3 TRUTH TABLE Logic 0 1 SW1, SW4 ON OFF SW2, SW3 OFF ON ORDERING INFORMATION Temp Range DG9424/9425 DG9424DQ --40 to 85_C 40 16-Pin 16 Pin TSSOP DG9425DQ Package Part Number DG9426 --40 to 85_C 16-Pin TSSOP DG9426DQ ABSOLUTE MAXIMUM RATINGS V+ to V-- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 TO 13 V GND to V-- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND --0.3 V) to (V+) +0.3 V IN, COM, NC, NOa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 to (V+ +0.3 V) Continuous Current (NO, NC, COM Pins) . . . . . . . . . . . . . . . . . . . . . 100 mA Peak Current, S or D (Pulsed 1 ms, 10% Duty Cycle) . . . . . . . . . . . . 200 mA Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --65 to 150_C Notes: a. Signals on NC, NO, COM or IN exceeding V+ or V-- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to PC Board. c. Derate 5.6 mW/_C above 70_C Power Dissipation (Package)b 16-Pin TSSOPc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW www.vishay.com 2 Document Number: 71807 S-31818--Rev. D, 01-Sep-03 DG9424/9425/9426 Vishay Siliconix SPECIFICATIONSa (SINGLE SUPPLY 12 V) Test Conditions Unless Specified Parameter Analog Switch Analog Signal Rangee On-Resistance VANALOG rON V+ = 10.8 V, V-- = 0 V INO, INC = 50 mA, VCOM = 2/9 V Full Room Full 0 1.8 12 3 4 V Limits --40 to 85_C Symbol V+ = 12 V V-- = 0 V V, VL = 5 V, VIN = 2.4 V, 0.8 Vf Tempb Mind Typc Maxd Unit Digital Control Input Current IINL or IINH Full --1 0.01 1 mA Dynamic Characteristics Turn-On Timee Turn-Off Timee Break-Before-Make Time Delaye Charge Injectione Off Isolatione Channel-to-Channel Crosstalke NO, NC Off Capacitancee COM Off Capacitancee Capacitancee tON tOFF tD QINJ OIRR XTALK CNO(off) CNC(off) CCOM(off) CCOM(on) f = 1 MH MHz RL = 300 , CL = 35 pF VNO, VNC = 5 V See Figure 2 DG9426 Only, VNO, VNC = 5 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF RL = 50 , CL = 5 pF, f = 1 MHz Room Full Room Full Room Room Room Room Room Room Room 2 38 --56 --77 49 37 89 pF F dB pC 42 28 57 65 42 44 ns Channel On Power Supplies Positive Supply Current Negative Supply Current Logic Supply Current Ground Current I+ I-VIN = 0 or VL IL IGND Room Full Room Full Room Full Room Full --1 --5 --1 --5 0.02 --0.002 0.002 --0.002 1 5 mA 1 5 SPECIFICATIONSa (DUAL SUPPLY 5 V) Test Conditions Unless Specified Parameter Analog Switch Analog Signal Rangee On-Resistance VANALOG rON INO(off) INC(off) ICOM(off) ICOM(on) V+ = 4.5 V, V-- = --4.5 V INO, INC = 50 mA, VCOM = 3.5 V V+ = 5.5 V, V-- = --5.5 V VCOM = 4.5 V, VNO, VNC = 4.5 V V+ = 5.5 V, V-- = --5.5 V VNO, VNC = VCOM = 4.5 V Full Room Full Room Full Room Full Room Full --1 --10 --1 --10 --1 --10 --5 2 5 3.3 4.3 1 10 1 10 1 10 nA V Limits --40 to 85_C Symbol V+ = 5 V V-- = --5 V V, VL = 5 V, VIN = 2.4 V, 0.8 Vf Tempb Mind Typc Maxd Unit Switch Off Leakage Current Channel On Leakage Current Digital Control Input Currenta IINL or IINH Full --1 0.05 1 mA Document Number: 71807 S-31818--Rev. D, 01-Sep-03 www.vishay.com 3 DG9424/9425/9426 Vishay Siliconix SPECIFICATIONSa (DUAL SUPPLY 5 V) Test Conditions Unless Specified Parameter Dynamic Characteristics Turn-On Timee Turn-Off Timee Break-Before-Make Time Delaye Charge Injectione Off Isolatione Channel-to-Channel Crosstalke Source Off Capacitancee Drain Off Capacitancee tON tOFF tD QINJ OIRR XTALK CNO(off) CNC(off) CCOM(off) CCOM(on) f = 1 MH MHz RL = 300 , CL = 35 pF VNO, VNC = 3.5 V See Figure 2 DG9426 Only, VNO, VNC = 3.5 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF RL = 50 , CL = 5 pF, f = 1 MHz Room Full Room Full Room Room Room Room Room Room Room 2 112 --56 --82 38 38 89 pF F dB pC 56 42 74 81 64 67 ns Limits --40 to 85_C Symbol V+ = 5 V, V-- = --5 V VL = 5 V, VIN = 2.4 V, 0.8 Vf Tempb Mind Typc Maxd Unit Channel On Capacitancee Power Supplies Positive Supply Currente Negative Supply Currente Logic Supply Currente Ground Currente I+ I-VIN = 0 or VL IL IGND Room Full Room Full Room Full Room Full --1 --5 --1 --5 0.03 --0.002 0.002 --0.002 1 5 mA 1 5 SPECIFICATIONSa (SINGLE SUPPLY 5 V) Test Conditions Unless Specified Parameter Analog Switch Analog Signal Rangee On-Resistancee VANALOG rON V+ = 4.5 V, INO, INC = 50 mA VCOM = 1 V, 3.5 V Full Room Full 3.4 5 4.8 5.8 V Limits --40 to 85_C Symbol V+ = 5 V V-- = 0 V V, VL = 5 V, VIN = 2.4 V, 0.8 Vf Tempb Mind Typc Maxd Unit Dynamic Characteristics Turn-On Timee Turn-Off Timee Break-Before-Make Time Delaye Charge Injectione tON tOFF tD QINJ RL = 300 , CL = 35 pF VNO, VNC = 3.5 V, See Figure 2 DG9426 Only, VNO, VNC = 3.5 V, RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF Room Hot Room Hot Room Room 5 10 pC 71 37 86 106 51 56 ns Power Supplies Positive Supply Currente Negative Supply Currente Logic Supply Currente Ground Currente I+ I-VIN = 0 or VL IL IGND Room Hot Room Hot Room Hot Room Hot --1 --5 --1 --5 0.02 --0.002 0.002 --0.002 1 5 mA 1 5 www.vishay.com 4 Document Number: 71807 S-31818--Rev. D, 01-Sep-03 DG9424/9425/9426 Vishay Siliconix SPECIFICATIONSa (SINGLE SUPPLY 3 V) Test Conditions Unless Specified Parameter Analog Switch Analog Signal Rangee On-Resistance VANALOG rON INO(off) INC(off) ICOM(off) ICOM(on) V+ = 2.7 V, V-- = 0 V INO, INC = 5 mA, VCOM = 0.5, 2.2 V V+ = 3.3 V, V-- = 0 V VCOM = 0.3, 3 V, VNO, VNC = 3, 0.3 V V+ = 3.3 V, V-- = 0 V VNO, VNC = VCOM = 0.3, 3 V Full Room Full Room Full Room Full Room Full --1 --10 --1 --10 --1 --10 0 8 3 13.8 15.1 1 10 1 10 1 10 nA V Limits --40 to 85_C Symbol V+ = 3 V V-- = 0 V V, VL = 3 V, VIN = 2.4 V, 0.4 Vf Tempb Mind Typc Maxd Unit Switch Off Leakage Currenta Channel On Leakage Currenta Digital Controle Input Current IINL or IINH Full --1 0.005 1 mA Dynamic Characteristics Turn-On Time Turn-Off Time Break-Before-Make Time Delay Charge Injectione tON tOFF tD QINJ OIRR XTALK CNO(off) CNC(off) CCOM(off) CCOM(on) f = 1 MH MHz RL = 300 , CL = 35 pF VNO, VNC = 1.5 V See Figure 2 DG9426 Only, VNO, VNC = 1.5 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF RL = 50 , CL = 5 pF, f = 1 MHz Room Full Room Full Room Room Room Room Room Room Room 5 15 --56 --80 53 42 92 pF F dB pC 140 65 163 193 80 89 ns Off Isolatione Channel-to-Channel Crosstalke Source Off Capacitancee Drain Off Capacitancee Channel On Capacitancee Notes: a. Leakage parameters are guaranteed by worst case test conditions and not subject to production test. b. Room = 25_C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. f. VIN = input voltage to perform proper function. Document Number: 71807 S-31818--Rev. D, 01-Sep-03 www.vishay.com 5 DG9424/9425/9426 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) 1 10 rON vs. VCOM and Supply Voltage T = 25_C IS = 50 mA 12 rON vs. Analog Voltage and Temperature IS = 50 mA A = 85_C B = 25_C C = --40_C V+ = 2.7 V 8 r ON -- On-Resistance ( ) VCC = 2.7 V 6 r ON -- On-Resistance ( ) 10 8 A 6 B C 4 V+ = 4.5 V A B C 2 4 VCC = 4.5 V 2 VCC = 10.8 V 0 0 3 6 9 12 VCOM -- Analog Voltage (V) 0 0 1 2 3 4 5 VCOM -- Analog Voltage (V) 8 7 r ON -- On-Resistance ( ) 6 5 4 3 2 1 0 --5 rON vs. Analog Voltage and Temperature V = 5 V IS = 50 mA A = 85_C B = 25_C C = --40_C I+ -- Supply Current (pA) Supply Current vs. Temperature 100 V+ = 5 V VIN = 0 V A B C --3 --1 1 3 5 10 --40 --20 0 20 40 60 80 100 VCOM -- Analog Voltage (V) Temperature (_C) Leakage Current vs. Analog Voltage 60 V+ = 5 V V-- = --5 V I+ -- Supply Current (A) Switching Current vs. Input Switching Frequency 100 m 10 m 1m 100 m 10 m 1m 100 n 10 n V+ = 5 V V-- = --5 V 40 Leakage Current (pA) 20 ICOM(on) 0 INO(off)/INC(off) --20 ICOM(off) --40 --60 --5 --3 --1 1 3 5 1n 10 100 1K 10 K 100 K 1M 10 M VCOM, VNO, VNC -- Analog Voltage www.vishay.com Input Switching Frequency (Hz) Document Number: 71807 S-31818--Rev. D, 01-Sep-03 6 DG9424/9425/9426 Vishay Siliconix TYPICAL CHARACTERISTICS (25_C UNLESS NOTED) Switching Time vs. Temperature and Single Supply Voltage 180 120 VSUPPLY = 5 V 150 tON V+ = 3 V 120 80 100 Switching Time vs. Temperature and Dual Supply Voltage 90 tON V+ = 5 V tOFF V+ = 3 V tON V+ = 12 V tOFF V+ = 5 V tOFF V+ = 12 V 60 tON VS = --3.5 V tON VS = 3.5 V 60 40 tOFF VS = --3.5 V 20 tOFF VS = 3.5 V 30 0 --60 --40 --20 0 20 40 60 80 100 0 --60 --40 --20 0 20 40 60 80 100 Temperature (_C) Temperature (_C) Leakage Current vs. Temperature 1000 V+ = 5 V V T -- Switching Threshold (V) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 1 --60 --40 --20 0 20 40 60 80 100 0.0 2 Switching Threshold vs. Supply Voltage Leakage Current (pA) 100 ICOM(on) 10 ICOM(off) 4 6 8 10 12 14 Temperature (_C) V+ -- Supply Voltage (V) Insertion Loss, Off Isolation and Crosstalk vs. Frequency 10 0 --10 --20 Loss (dB) --30 --40 --50 --60 --70 --80 --90 100 K 1M 10 M Frequency (MHz) Document Number: 71807 S-31818--Rev. D, 01-Sep-03 100 M 1G Crosstalk Off Isolation V+ = 3 V V-- = 0 V RL = 50 Insertion Loss --3 dB = 280 MHz www.vishay.com 7 DG9424/9425/9426 Vishay Siliconix SCHEMATIC DIAGRAM (TYPICAL CHANNEL) V+ S VL V-VIN Level Shift/ Drive V+ GND D V-- FIGURE 1. TEST CIRCUITS VL V+ Logic Input VINH 50% VINL tr <5 ns tf <5 ns tOFF VL VIN NO or NC IN GND V+ COM VOUT VOUT RL 300 CL 35 pF 0V tON 90% 0.9 x VOUT V-- Switch Output Switch V-CL (includes fixture and stray capacitance) VOUT = VIN RL RL + rON Note: Logic input waveform is inverted for switches that have the opposite logic sense control FIGURE 2. Switching Time VL V+ Logic Input VIN1 VIN2 NO1 IN1 NC2 IN2 GND V-COM2 VO2 Switch Output RL1 300 RL2 300 CL2 35 pF CL1 35 pF Switch Output 0V VIN2 VO2 0V COM1 3V 50% 0V VIN1 VO1 VO1 90% 90% tD tD V-CL (includes fixture and stray capacitance) FIGURE 3. Break-Before-Make (DG9426) www.vishay.com 8 Document Number: 71807 S-31818--Rev. D, 01-Sep-03 DG9424/9425/9426 Vishay Siliconix TEST CIRCUITS VL V+ VO Rg VL COM IN GND V-INX V-VIN = 0 -- V+ V+ NO or NC VOUT CL 10 nF OFF ON Q = VO x CL OFF INX OFF ON OFF VO Vg INX dependent on switch configuration Input polarity determined by sense of switch. FIGURE 4. Charge Injection C VL V+ C V+ COM1 50 VS Rg = 50 0V, 2.4 V VL NO1 IN1 NO2 NC 0V, 2.4 V IN2 GND VOUT VIN COM2 RL V-C VOUT XTALK Isolation = 20 log C = RF bypass V-- FIGURE 5. Crosstalk VL C VL NO or NC V+ V+ C C VL VOUT V+ VIN Rg = 50 0V, 2.4 V COM C VL V+ IN RL 50 GND V-C 0 V, 2.4 V IN COM Meter HP4192A Impedance Analyzer or Equivalent C NO or NC V-GND Off Isolation = 20 log C = RF Bypass VOUT VIN V-V-- FIGURE 6. Off Isolation FIGURE 7. Source/Drain Capacitances Document Number: 71807 S-31818--Rev. D, 01-Sep-03 www.vishay.com 9 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1 |
Price & Availability of DG942408 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |